Wireless Video Doorbell Installation Guide: Set Up in 10 Minutes, No Electrician

Ved Patel

Introduction

One of the biggest reasons Indian homeowners hesitate before buying a video doorbell is the assumption that installation requires an electrician, wall drilling, and a half-day of disruption. That assumption comes from wired doorbells and it simply doesn’t apply to wireless ones.

A wireless video doorbell installation is genuinely one of the simplest DIY tasks you can do at home. No cables. No transformer. No electrical knowledge required. Just a phone, a Wi-Fi connection, and about 10 minutes of your time.

This guide walks you through the complete setup process from unboxing to your first live view step by step, in plain language.

What’s Inside the Box

Before you begin, unbox your Delitech doorbell and confirm all components are present. Every Delitech wireless video doorbell ships with:

  • Video doorbell unit

  • Wireless indoor chime

  • Mounting bracket

  • Double-sided tape

  • Wall anchors and screws

  • Screwdriver

  • USB charging cable

  • Reset pin

  • AAA batteries for the chime

  • Quick start guide

Having everything laid out before you start makes the process faster and smoother. If anything is missing, contact the Delitech support team before proceeding; they're available 24x7.

Before You Start Two Things to Check

Check your Wi-Fi signal at the front door

Your wireless video doorbell connects to your home’s 2.4GHz Wi-Fi network. Before mounting anything, take your phone to your front door and check the Wi-Fi signal strength there. If the signal is weak or drops frequently at that location, a basic Wi-Fi extender available for ₹800 to ₹1,500 at most electronics stores will solve the problem before it becomes one. A strong Wi-Fi signal also directly extends battery life, as the doorbell uses less power maintaining a stable connection. This relationship between Wi-Fi strength and battery performance is covered in detail in our wireless video doorbell battery life guide.

Decide where you want to mount it 

The ideal mounting height for a video doorbell is between 1.2 and 1.5 metres from the ground, roughly chest height for an average Indian adult. At this height, the camera captures a clear face-level view of visitors without too much sky or ground in the frame. Make sure the chosen spot has a clean, flat surface and is within Wi-Fi range.

Step 1: Charge the Doorbell Fully

Before anything else, connect the doorbell to a power source using the included USB charging cable and charge it fully. A complete first charge takes approximately 3 to 4 hours.

Charging before installation is important for two reasons: it confirms the device is working correctly before you mount it, and it ensures you start with maximum battery life. Do not skip this step even if the doorbell shows some charge out of the box.

Step 2: Set Up the Indoor Chime

Insert the included AAA batteries into the wireless chime. Plug the chime into any standard 5-amp wall socket inside your home, the living room, bedroom, or anywhere you spend most of your time. The chime pairs automatically with the doorbell and requires no app configuration or manual pairing steps.

You can place the chime on any floor of your home. For multi-storey houses, if you want a chime on each floor, the Delitech Wireless Indoor Chime is available separately at ₹799 and pairs with all Delitech doorbell models automatically.

Step 3: Download the CloudEdge App and Create an Account

Download the CloudEdge app from the Google Play Store, Apple App Store, or Amazon Appstore on your smartphone. Create a free account using your mobile number or email address.

Once logged in, tap the “+” icon to add a new device. The app will guide you through connecting the doorbell to your home Wi-Fi network. You’ll need your Wi-Fi password at this step, so keep it handy. The connection process takes approximately 3 to 5 minutes.

According to Google Play Store guidelines on smart home app setup, apps that use QR-based or guided Wi-Fi pairing like CloudEdge consistently deliver faster, more reliable device connections than manual IP-based pairing methods. This is why the CloudEdge setup process is smooth even for first-time smart home users.

Step 4: Choose Your Installation Method

This is where wireless doorbell installation gives you flexibility that wired doorbells never could. You have two options to choose based on your home type and preference.

Option A - Double-Sided Tape (No Drilling)

This is the recommended method for apartments, rented homes, and any wall surface where drilling is difficult such as tiles, stone, or glass.

Clean the wall surface at your chosen mounting spot with a dry cloth to remove dust or grease. Peel the backing off the included double-sided tape and press it firmly onto the back of the mounting bracket. Press the bracket firmly against the wall for 30 seconds to ensure a strong bond. The doorbell clips onto the bracket and locks into place.

That’s it. No drilling, no wall damage, completely reversible. When you move out or want to reposition the device, the bracket peels off cleanly without leaving marks.

Option B - Screw Mount (More Permanent)

For independent houses, bungalows, or anyone who wants a more permanent, sturdy installation the screw mount is the better choice.

Hold the mounting bracket against the wall at your chosen height and mark the screw positions with a pencil. Use the included screwdriver to make pilot holes if needed, insert the wall anchors, and screw the bracket firmly into place. The doorbell clips and locks onto the bracket.

The entire process takes under 10 minutes and requires no electrical work of any kind. If you’re unsure which installation type suits your home best, our guide on wireless video doorbells for homes without existing wiring explains both methods alongside India-specific home types in detail.

Step 5: Mount the Doorbell and Angle It Correctly

Once the bracket is fixed, clip the doorbell unit onto it and lock it into position. Before finalising the angle, open the CloudEdge app and check the live camera view on your phone. Adjust the doorbell angle tilting up, down, or sideways until your entrance frame is centred in the view with a clear line of sight to where visitors typically stand.

If you want to optimize the viewing angle further, the Delitech adjustable mounting bracket at ₹1,199 offers greater tilt flexibility than the standard bracket particularly useful for corner walls or entrances where the doorbell needs to face at an angle.

Step 6: Configure Motion Detection and Alerts

With the doorbell mounted and connected, open the CloudEdge app and spend 3 to 4 minutes configuring two settings that make a significant difference to daily use:

Detection Zones 

Rather than triggering every movement in the full camera frame passing vehicles, pedestrians on the street, stray animals set a specific detection zone covering just your gate or doorstep. This dramatically reduces unnecessary alerts and is one of the most effective ways to extend battery life between charges.

Alert Sensitivity 

Adjust the motion sensitivity to match your entrance activity level. High sensitivity works well for quiet residential areas. Medium sensitivity is better for busier streets where the camera picks up background movement frequently.

Step 7: Test Everything

Before considering the installation complete, run a quick test:

  • Press the doorbell button from outside confirm the chime rings inside and your phone receives a notification

  • Open the live view in the CloudEdge app and check video clarity

  • Speak into the doorbell and confirm two-way audio works clearly in both directions

  • Trigger a motion event and confirm the motion alert arrives on your phone within a few seconds

If everything works your wireless video doorbell installation is complete.

Which Delitech Doorbell Are You Installing?

The installation process above applies to all Delitech wireless video doorbells. The right model for your home depends on your entrance size and resolution needs.

For apartments and compact entrances, the Delitech 2MP at ₹6,999 and Delitech 1MP at ₹5,499 are the most straightforward choices Full HD clarity at the most accessible prices. For independent houses, the Delitech 3MP Plus at ₹7,499 is the most popular option Super HD footage with sharper facial recognition at wider gate distances. For bungalows and larger properties, the Delitech 5MP Pro at ₹8,999 delivers 2K Ultra HD clarity from up to 5 metres.

If you’re still deciding which resolution fits your home, our 2MP vs 3MP vs 5MP video doorbell comparison breaks it down clearly with a side-by-side guide.

Conclusion

A wireless video doorbell installation takes 10 minutes, costs nothing in labour, and requires no electrical knowledge. Charge the device, set up the chime, connect the app, mount with tape or screws, configure your alerts, and test. That’s the entire process.

If you run into any issue at any step, the Delitech support team is available 24x7 by phone, WhatsApp, and email and free installation assistance is included with every purchase. Browse the complete Delitech video doorbell range and get your home secured today.

FAQs

Do I need an electrician to install a wireless video doorbell? 

No, wireless video doorbells require zero electrical work. The installation involves mounting a bracket with tape or screws and connecting to Wi-Fi through the app. It takes under 10 minutes and no professional help is needed.

Can I install a wireless video doorbell in a rented apartment? 

Yes, the double-sided tape installation option leaves no permanent marks on the wall and is fully reversible. It is the most popular installation method among Indian apartment renters.

What height should I mount my video doorbell? 

The ideal mounting height is between 1.2 and 1.5 metres from the ground, approximately chest height for an average adult. This gives the camera the best angle for capturing clear face-level views of visitors.

What if I need to adjust the viewing angle after mounting?

If the standard bracket doesn’t give enough tilt flexibility for your wall position, the Delitech adjustable mounting bracket offers greater angle control and is available separately at ₹1,199.

Does the chime need to be set up separately? 

No, insert the batteries, plug it into any wall socket, and the chime pairs with the doorbell automatically. There are no additional pairing steps or app configuration required.

Back to blog